Using DWDM, a single fiber can carry between what two numbers of channels?​
a.
​60
b.
​80
c.
​160
d.
​200
answer
b.
​80
c.
​160
question
What two items below are commonly expressed as bits transmitted per second?
a.
frequency
b.
​amplitude
c.
​throughput
d.
​bandwidth
answer
c.
​throughput
d.
​bandwidth
question
8. ​What two connector types are typically used to terminate RG-6 and RG-59 cables?
a.
​f-connectors
b.
​BNC
c.
​ST couplers
d.
J-hooks
answer
a.
​f-connectors
b.
​BNC
question
Frequencies used to convey speech over telephone lines fall between what two frequencies below?​
a.
​100 Hz
b.
​300 Hz
c.
​3.3 KHz
d.
​5.5 KHz
answer
b.
​300 Hz
c.
​3.3 KHz
question
What is the maximum supported throughput and bandwidth / signal rate of Cat 5e?​
a.
​100 Mbps
b.
​1000 Gbps
c.
​100 MHz
d.
​350 MHz
answer
b.
​1000 Gbps
d.
​350 MHz
question
What term below is used to describe the outer-most layer of protective covering of a coaxial cable?
a.
​sheath
b.
​shield
c.
​braiding
d.
​insulation
answer
a.
​sheath
question
What Ethernet standard below is also referred to as "thinnet"?​
a.
​100Base2
b.
​10Base2
c.
​100BaseT
d.
​10BaseT
answer
b.
​10Base2
question
What is the minimum category of UTP cable required in order to support Gigabit speeds?​
a.
​Cat 3
b.
​Cat 5
c.
​Cat 5e
d.
​Cat 6
answer
c.
​Cat 5e
question
. What is the maximum supported throughput of a CAT6 cable?​
a.
​100 Mbps
b.
​1 Gbps
c.
​10 Gbps
d.
​100 Gbps
answer
c.
​10 Gbps
question
20. How many cable pairs are needed for 1000Base-T transmission over CAT5e cable?​
a.
​2
b.
​4
c.
​6
d.
​8
answer
b.
​4
question
Standard PoE devices ​must be provided with how much power in order to function?
a.
​5 watts
b.
​12 watts
c.
​15.4 watts
d.
​25.5 watts
answer
c.
​15.4 watts
question
What is the maximum distance for 10GBase-ER and 10GBase-EW on a segment of single mode fiber?​
a.
​550m
b.
​300m
c.
10km
d.
​40km
answer
d.
​40km
question
What type of cross-talk occurs between wire pairs near the source of a signal? ​
a.
​far end cross talk
b.
​near end cross talk
c.
​alien cross talk
d.
pair migration cross talk
answer
b.
​near end cross talk
question
Which of the following connectors is the most common for multimode fiber?​
a.
​ST
b.
​SC
c.
​FC
d.
​MT-RJ
answer
d.
​MT-RJ
question
A measure of a signal's strength at any given time is known as which term below?
a.
​amplitude
b.
​frequency
c.
​phase
d.
​wavelength
answer
a.
​amplitude
question
The number of times that a wave's amplitude cycles from its starting point, through its highest amplitude and its lowest amplitude, and back to its starting point over a fixed period of time, is known as ​what term below?
a.
​amplitude
b.
​frequency
c.
​wavelength
d.
​phase
answer
b.
​frequency
question
WDM divides a beam of light into how many different wavelengths or colors?
a.
​10
b.
​20
c.
​30
d.
​40
answer
d.
​40
question
. Which type of multiplexing is defined by wavelength instead of frequency?​
a.
​CWDM
b.
​DWDM
c.
​WDM
d.
​FDM
answer
a.
​CWDM
question
. ​Which option below reflects the standard impedance of an RG-6 cable?
a.
​50 ohms
b.
​60 ohms
c.
​65 ohms
d.
​75 ohms
answer
d.
​75 ohms
question
Phone companies make use of what type of multiplexing in order to allow for phone services and DSL services over the same line?​
a.
​WDM
b.
​FDM
c.
​DWDM
d.
​CWDM
answer
b.
​FDM
question
The most common multiplexing technology used in conjunction with fiber optics is which option below?​
a.
​DWDM
b.
​CWDM
c.
​FDM
d.
​WDM
answer
a.
​DWDM
question
A device that is responsible for modulating digital signals into analog signals, and demodulating analog signals into digital signals at the receiving end, is known as?​
a.
​A modem
b.
​A transceiver
c.
​A demuxer
d.
​A multiplexer
answer
a.
​A modem
question
Ethernet is an example of what type of technology?​
a.
​broadband
b.
​baseband
c.
​wideband
d.
​narrowband
answer
b.
​baseband
question
34. Since cable TV and cable ​Internet can share the same coaxial cable, they are considered to be what type of technology?
a.
​broadband
b.
​baseband
c.
​narrowband
d.
​wideband
answer
a.
​broadband
question
35. Using a form of transmission that allows multiple signals to travel simultaneously over one medium is known as which of the following options?​
a.
embedding
b.
​multiplexing
c.
​coupling
d.
​modulating
answer
b.
​multiplexing
question
A Physical layer standard for networks that
achieves 1 Gbps over Cat 6 or better cabling using only two
pairs of wires.
answer
b.
1000Base-TX​
question
42. A character encoding system consisting of 128 characters.​
ANSWER:
answer
​ASCII
question
A term used to refer to a type of twisted-pair cable. All of the category cables fall under the TIA/EIA 568 standard.
answer
CAT
question
A form of transmission that allows multiple signals to travel simultaneously over one medium.​
answer
multiplexing
question
45. An unwanted connection, such as when exposed wires touch each other.​
answer
short circuit​
question
Physical layer standard for networks that specifies 1-Gbps transmission over fiber-optic cable using baseband transmission, relying on 1300 nanometer wavelengths.​
answer
1000Base-LX
question
47. The distance between corresponding points on a wave's cycle, expressed in meters or feet.
answer
wavelength
question
Cross-talk measured at the far end of the cable from the signal source. ​
answer
far end cross-talk (FEXT)​
question
The amount of data that a medium transmits during a given period of time.
answer
throughput
question
A multiplexing technique used over single-mode or multimode fiber-optic cable in which each signal is assigned a different wavelength for its carrier wave.​
answer
DWDM (Dense Wavelength Division Multiplexing)
Haven't found what you need?
Search for quizzes and test answers now
Quizzes.studymoose.com uses cookies. By continuing you agree to our cookie policy